The Association of Rotational Moulders of Southern Africa (ARMSA) - Email: info@armsa.co.za

News & Blog

2018 Winner of Sasol sponsored Student Design Competition announced

News & Blog

The Sasol sponsored Student Design Competition was started after a visit to the Australian rotomoulding conference in the early 2000’s, where they were running a design competition for students. We thought that it was something which could be done in South Africa through ARMSA, with the initial aim of promoting growth in the local rotomoulding market. Sasol has been sponsoring the competition from inception . Little did we know how things would go, and what a success it would be.

The first problem was where to start. Would it be an open competition or something more targeted. We contacted the lecturers at Technikon Witwatersrand (as it was called then) running the Industrial Design course, and they suggested a project for the second year students. After some teething problems we have reached a point where we are working with the University of Johannesburg, and the Tshwane University of Technology that have a rotomoulding project for their second year students, i.e. rotomoulding is part of the curriculum at these two places, and who participate in the competition.  We aim to expand to work with others centres as well. The lecturers like the project because the brief is much wider than for other projects that they do. For example a brief might be “Design a kettle”, which is quite specific, whereas the brief for this year’s rotomoulding project is “Outdoor Sports and Recreation”. This requires the students to think and research extensively.

The process that we go through each year is the following:

  • Between the ARMSA committee and the lecturers we agree a brief for the project.
  • Once a date is agreed for the start of the project one of the ARMSA committee gives a lecture on rotomoulding to the students, give them background information.
  • The lecturer will normally organise a visit to a local rotomoulder so that the students can see the process, and ask further questions.
  • The students produce the work for their project, which is assessed by the lecturers as part of their course work. However what has been done is their entry into the competition. They do not have to do anything else.
  • Set a judging date, and this is attended by the ARMSA committee and the lecturers
  • Once judging is done, the winners are announced either at the next ARMSA conference, or via a visit to the university, depending on the timing.
  • There is of course prize money for the first three students, and sometimes we award commendation to those which we think warrant it.
The panel judging

One important thing that we do is to make sure that all the entries are exhibited at the conference. Not all the models are used, in case they get damaged, but all the renderings are displayed. This is important as it showcases the student’s work, but also there may be a moulder who wished to develop the design further with a particular student. Some feedback that we have had from the lecturers is that sometimes where a student has not been doing that well in the year, and they get something out of the competition, then it gives them more enthusiasm for their course.

Designs on Display at the Conference

An innovation introduced this year was that ARMSA sponsored the manufacture of a mould of  the winning design so that a full moulded prototype could be shown at the conference. This proved to be very successful.

2017 Winner –Pierre Botha with Wayne Wiid
(ARMSA Chairman) and Nick Aggett

One success that we have had with the project is a product designed by Jed Aylmer, who was an industrial design student in 2013 at the University of Johannesburg, and who took part in the competition. Subsequent to graduating, he has started a company and designed a product called the Symba Pediatric Bed which is in use at the Nelson Mandela Children’s Hospital (shown below).

Source: www.praestet.com

So, if Jed Aylmer had not been exposed to rotomoulding through the second year project, the Symba bed would probably not have been a rotomoulded product. This is exactly what the competition sets out to do, make industrial design students aware of rotomoulding and what can be done with it.

Lastly, ARMSA would like to thank Sasol for their continuous support for this competition, as well as the lecturers at the universities, and the students who have given us some great designs.

 

Leave a Reply

Your email address will not be published. Required fields are marked *